ROTH TECHNOLOGIES · CATHETER DESIGN ENGINEERINGQuestions? sales@cathcad.com
CathCAD® / Hypotube

Interrupted helical hypotube modeling.

Explore how laser-cut geometry changes hypotube flexibility, axial and torsional rigidity, bend behavior, and radial crush resistance.

CathCAD® Hypotube modeling is part of the CathCAD® family and is included with the software license at no additional charge to licensed users.

Machined stainless steel hypotube transitioning from a smooth tube section to an interrupted helical cut pattern
Interrupted helical hypotube configuration
Hypotube resources

Downloads and support

Product-specific files are grouped here for installation, use, and review.

The Hypotube installer is not available yet and is expected this week. The User Guide and reports are available below. Installer filenames use the stable, unversioned standard.

01 / Geometry inputs

Define the cut pattern

Set the tube dimensions and interrupted helical pattern. CathCAD® Hypotube displays derived dimensions such as inside diameter and uncut bridge span.

Parameterized design inputs

Outside diameter, Do
2.000 mm
Wall thickness, t
0.100 mm
Inside diameter, Di
1.800 mm
Kerf, normal to path, k
0.030 mm
Helical pitch, P
4.000 mm/turn
Cut angular span
80.00°
Cuts per turn
3.5
Uncut bridge span
22.857°
Section length, L
8.000 mm
Material
304 Stainless Steel · Annealed

Illustrative input set from the five-case comparison. Pitch varies between the slotted cases; the other listed geometry and material inputs are held constant.

02 / CathCAD® Hypotube interface

Inputs and predicted mechanical response

The interface brings geometry, material inputs, the tube visualization, and calculated outputs together in one design workflow.

CathCAD® Hypotube interface with geometry and material input fields, developed laser unwrap, 3D metallic tube view, cross-section diagram, and model outputs
CathCAD® Hypotube interface. The displayed run is an example view of the software.
03 / Five-case comparison

Mechanical response across helical pitch

Annealed 304 stainless steel hypotube comparison using the rerun dataset. Table values are shown directly; the chart summarizes retention relative to the solid baseline.

Do 2.000 mmWall 0.100 mmID 1.800 mm304 Stainless Steel · AnnealedKerf 0.030 mm80° cut span3.5 cuts/turnSection 8.000 mm
Mechanical PropertyUnitsCase 1
Solid Baseline
Case 2
P = 4.00 mm
Case 3
P = 1.00 mm
Case 4
P = 0.50 mm
Case 5
P = 0.25 mm
EI Flexural RigidityN·mm²52,24843,02523,00412,8176,769
EA Longitudinal RigidityN115,20094,96953,39030,35916,536
Torsional Rigidity (GJ)N·mm²40,55038,06130,05020,34111,194
Failure / Kink Bend Radiusmm28.431.441.154.274.3
Permanent-Set Bend Radius (0.2% Offset)mm303.5286.1221.2151.7125.4
Crush Resistance @ 5%N/mm13.7712.358.655.552.96

Lower Permanent-Set Radius indicates tighter recoverable bending without permanent curvature; Failure / Kink Radius indicates structural Brazier collapse. Crush resistance is normalized per unit axial length.

Two charts: stiffness and crush retention compared with solid baseline, and permanent-set radius versus structural kink radius across five hypotube cases
04 / Model validation

Analytical checks

The CathCAD® Hypotube validation report documents ten plain-tube analytical checks. Reported results are within 5% of their analytical references. The report covers analytical model checks; it does not report physical bench testing.

Download the CathCAD® Hypotube Validation Report (Word, R00) ↓
Superelastic Nitinol verification

Verification of material selection, stiffness and crush response, the 6% recoverable-strain criterion, and kink / kerf-closure behavior.

Download PDF report · Revision R00 ↓

CathCAD® Hypotube modeling is the latest addition to the CathCAD® family, alongside Standard, Advanced, and MultiLumen.

Included at no additional charge for licensed CathCAD® users.